A practical guide to panel types, technical specifications, standards, engineering, manufacturing quality and supplier selection for projects in Chennai and Sriperumbudur.
Choosing the right electrical panel manufacturer for your factory, commercial, infrastructural & industrial project is key. Electrical panels are used to distribute, control & protect the electrical systems. Choosing the right manufacturer can have a direct impact on your plant.
Chennai & surrounding industrial areas such as Sriperumbudur will have a wide range of requirements for electrical panels. These could include Power Control Centre (PCC) panels, Motor Control Centre (MCC) panels, Automatic Power Factor Control (APFC) panels, Variable Frequency Drive (VFD) panels, AMF panels and specialist automation panels.
When choosing your panel supplier you should also look at the engineering capabilities, components, standards and testing, quality of manufacture, paperwork and customer support.
This article will show you how to shortlist an electrical panel manufacturer for projects in Chennai & Sriperumbudur, what Technical Specifications to look out for and what common mistakes to avoid.
Table of Contents
Why choosing the right electrical panel is important
Types of Electrical Panels Required by Industries
Industrial Electrical Panel Requirements in Chennai and Sriperumbudur
How to Choose an Electrical Panel Manufacturer
Important Technical Specifications to Check
Electrical Panel Standards and Testing
Importance of Engineering Drawings and Documentation
Manufacturing Quality and Inspection
How to Compare Electrical Panel Quotations
Questions to Ask Before Placing an Order
Common Mistakes to Avoid
Choosing Super Elmech Engineers for Your Project
Frequently Asked Questions
Conclusion
1. Why choosing the right electrical panel is important
An electrical panel is a key component within any industrial electrical distribution and control system. It will allow electrical inputs to be distributed and control of electrical equipment.
Depending on the application within the manufacturing facility you may be using motors, pumps, compressors, production machines, conveyors, HVAC and more. Each of these will have different electrical demands.
A good quality panel should be engineered to take into account the actual electrical system.
What issues could cause by choosing the wrong panel?
Poor panel choice could cause:
- Frequent trips
- Overheating
- Low Short Circuit Withstanding
- Incorrect protection
- Difficult to maintain
- Issues with expansion
- Unnecessary downtime
The correct panel configuration will depend on the load schedule, voltage, current rating, fault level and the requirements of your project.
Quick Answer: You should ensure your electrical panel manufacturer can understand your requirements, look at the electrical design, suggest the correct components, provide drawings and explain what testing and paperwork is available.
2. Types of Electrical Panels
Before contacting any electrical panel manufacturers in Chennai it is important to know what type of electrical panel you will need. Below are some of the most common types of panels.
Power Control Centre (PCC) Panels
A Power Control Centre panel will mainly be used to receive electrical inputs and distribute to multiple outputs.
They are often a consideration for factories, industrial buildings, commercial buildings & large electrical systems.
Key considerations when choosing a PCC panel:
Incomer & Output Ratings
ACB’s & MCCB’s
Busbar Rating & Configuration
Short Circuit Withstanding
Metering & Protection
Cable Entries
Find out more about Power Control Centre (PCC) Panels
Motor Control Centre (MCC) Panels
An MCC panel will allow control and protection of multiple electric motors.
They could include motor starters, contactors, overload relays, breakers and controls.
Many industries would require an MCC panel if they have pumps, compressors, conveyors & production machines.
Find out more about Motor Control Centre (MCC) Panels
Automatic Power Factor Control (APFC) Panels
An APFC panel is used to control the switching of capacitor bank steps to help counteract reactive power requirements. This allows a set power factor.
They could be useful within an industrial setting where there are many inductive loads (e.g. motors & transformers).
Before choosing an APFC panel you should look at your current power factor, load variations, kVAR requirements & harmonic conditions.
Find out more about APFC Panels
Variable Frequency Drive (VFD) Panels
A VFD panel will allow control of compatible electric motors speeds by changing the frequency and voltage.
They are often used for pumps, fans, compressors & conveyors.
Ensure you have looked at drive sizing, motor compatibility, cooling, harmonic conditions, bypass requirements & control.
Find out more about VFD Panels
AMF & Synchronising Panels
An Automatic Mains Failure (AMF) panel will be used for generator systems. It will control the changeover between mains and generator, depending on the approved control philosophy.
A Synchronising panel will be used where there are multiple generators or power sources. The generators will need to be kept in synch.
You should know what protection, interlocking & sequence of operation will be required.
Specialist Industrial Control Panels
Depending on your project you may require:
PLC Control Panels
Load Sharing Panels
HVAC & AHU Control Panels
Fire Fighting Panels
Water Treatment Control Panels
Pump Control Panels
Thyristor APFC Panels
The manufacturer should have relevant experience in the type of panel you will require.
3. Electrical Panel Requirements in Chennai & Sriperumbudur
Chennai & Sriperumbudur are important sites for buying industrial products. When starting a new installation, expanding your factory or upgrading your electrical system you should consider what the actual site will be like.
A panel for use in a manufacturing unit may be completely different to one used in a commercial building or utility room.
Automotive & Component Manufacturing
If you have an Automotive or Component Manufacturing site you may have assembly lines, machine tools, conveyors, compressors & material handling systems.
This could require an MCC panel, VFD panel, PCC panel & controls to be used.
Electronics & Industrial Manufacturing
If you have an environment with electronic equipment, automated systems & production processes you will need a stable electrical distribution with the correct protection. Also the control system should be well documented.
The panel should be designed to suit the load being connected, operation & any specific power quality requirements.
Warehousing & Logistics
Large warehousing & logistics sites may have conveyors, pumps, ventilation, lighting & many other electrical loads.
Consider your power distribution, motor control & coordination.
Commercial & Infrastructural
Commercial buildings & infrastructural sites may require PCC, MCC, APFC, HVAC, Pump & specialist panels.
The design should be in line with the electrical drawings, operation & regulation.
What should I tell my panel manufacturer?
To get a meaningful technical quote you should give them the following information:
- Location & Installation Environment
- Load Schedule
- Single Line Diagram (SLD)
- Voltage & Current Requirements
- Fault Level
- Number & Rating of Outputs
- Type & Quantity of Panel Required
- Controls & Automation
- Project Specifications
- Delivery & Inspection Requirements
This will help them provide a more accurate technical & commercial proposal.
4. How to Choose an Electrical Panel Manufacturer
When shortlisting your electrical panel manufacturer you should look at the technical & commercial aspects.
Check they have experience in the correct type of panel.
Ask if the manufacturer has experience of supplying similar panels.
For example, if you require a complex synchronising/automation panel they may not have experience of general distribution panels.
Ask for examples of relevant projects they have completed. If they are allowed, ask for photos of the products & technical examples.
Check they have good engineering.
They should have a good process in place to look at the design, component choice, drawings & co-ordination with your team.
Ask if they can provide:
- Single Line Diagrams
General Arrangement Drawings
Control & Schematics
Bill of Materials
Component Specifications
Technical Submittals
Check the component choice.
They should clearly state what make/model/rating & Protection
The components will be.
Don’t just look at the brands within the quotation. Ensure they actually match the design.
Understand the testing.
Ask what inspections/testing will be carried out on the completed panel.
Ask if they can support you with inspecting or Factory Acceptance Testing (FAT).
Check they have good customer support.
Ask if they can provide support with installing, commissioning, troubleshooting & warranty.
Ask what will be included within the purchase order.
5. Key Technical Specifications
A suitable electrical panel should be suitable for the electrical and environmental requirements.
Voltage & Current Rating
Ensure you know what the voltage rating, insulation voltage (if applicable), current rating & incomer requirements are.
This should be suitable for the loads being connected.
Short Circuit Withstanding
Ensure the panel has a suitable short circuit withstanding for the prospective fault level.
Ask for supporting design verification/testing documentation.
Busbars
Ensure you know what make, size, current rating, fixings, insulation/sleeving (if applicable) & short circuit withstanding the busbars will be.
The busbars should be chosen based on the approved electrical design & verification requirements.
IP Rating
Ensure you know what IP rating the enclosure will have. This should be based on the installation environment.
For example, if you have a clean electrical room you may require a completely different enclosure setup than somewhere with dust/moisture.
Don’t just go for an IP rating without considering ventilation, heat dissipation & accessibility.
Protection & Metering
Ensure you know what circuit breakers, relays, current transformers, meters & protection will be used.
Ensure the protection settings are reviewed by the responsible electrical design team.
Cable Entries
Ensure you know what direction the cables will be coming in, gland plate configuration, termination space, door access & maintenance space.
6. Standards & Testing
A key consideration when looking at electrical panel manufacturers is the standards.
A key standard for low voltage switchgear & controlgear assemblies is the IEC 61439 series. You should also look at the relevant Indian Standards, statutory requirements, client requirements & project documentation.
What is Design Verification?
Design verification will show that the design of the assembly meets the requirements of the relevant standard.
Depending on what the requirements are, the design verification could cover temperature rise, dielectrics, short circuit withstanding & more.
What is Routine Verification?
Routine verification will be carried out on completed assemblies. This will ensure the assembly meets the relevant characteristics.
This should not be confused with type testing/design verification.
What should I be checking?
Before accepting any claims about testing, ask them:
- What standard & edition?
Test Report/Design Verification Documentation
Lab details (if applicable)
What design/product family will be tested?
What are the relevant current/fault ratings?
Are there any limitations?
Routine verification/inspections for the supplied panel.
Just because they have had a design tested by CPRI doesn’t mean each individual panel will have been type tested by CPRI. Ensure you have evidence.
7. Engineering Drawings
Engineering drawings are a key aspect when working with your panel manufacturer, consultant & contractor.
Single Line Diagram
This will show a simplified version of your electrical distribution. Including incomers, bus sections, protection & outputs.
General Arrangement
This will show the physical layout of the panel. Including size, sections, fixings & accessibility.
Controls & Schematics
This will show the controls, interlocks, wiring & sequence of operation.
Bill of Materials
This will show the main components, quantities & specifications.
Why should I approve the drawings?
By approving the drawings prior to manufacture you can identify incorrect output configurations, missing components, space issues & cable entries.
You should also have a formal process in place for reviewing any amendments. Manufacture should be done to the latest approved drawings.
8. Quality of Manufacture
A professional panel manufacturer should carry out quality checks.
Enclosure Manufacture
Ensure you know what quality of sheet metal has been used. This should include cutting, bending, welding, finish, door alignment & gland plates.
Component & Busbar Fixing
Ensure you know how the components have been fixed, busbars fixed, spacing, wiring, terminations & earthing.
Wiring
Ensure wiring has been carried out in accordance with the approved control drawings. The wiring should be clearly identified & terminated to make it easier to inspect & maintain.
Factory Acceptance Test
A Factory Acceptance Test may be included within your inspection plan.
Depending on what has been agreed, this could include:
- Visual & Mechanical Inspection
- Checking drawings & Bill of Materials
- Checking wiring & terminations
- Functionality
- Applicable Electrical Routine Verification
Checking inspection reports.
Agree what will be included within the Factory Acceptance Test, what the acceptance criteria will be & who will be witnessing the test.
9. How to Compare Electrical Panel Quotes
When comparing electrical panel manufacturers in Chennai or those supplying to Sriperumbudur ensure you provide the same technical specification to everyone.
Panel Type
PCC, MCC, APFC, VFD or Specialist Control Panel
Electrical Rating
Voltage, Current & Fault Level
Components
Make, Model, Rating & Protection
Busbars
Make, Rating & Fixing
Enclosure
Make, Size & IP Rating
Drawings
- Single Line Diagram, General Arrangement & Control Schematics
Standards
Applicable Standards & Verification
Testing
Routine Checks, Inspections & Agreed FAT
Delivery
Manufacture & Dispatch Timescales
Warranty
Warranty Details, Conditions & Duration
Customer Support
Installation, Commissioning & Service
Why shouldn’t I go for the cheapest quote?
A low quote may not include all the key components, engineering drawings, inspections, testing & commissioning.
A higher quote may include a more comprehensive technical package.
Ensure you compare the overall package & note down any differences. This will help to avoid any unexpected costs.
10. Questions to ask before ordering
Use the below checklist when discussing technical & commercial aspects.
- Can you manufacture the panel type we require?
- Can you review our SLD & Load Schedule?
- What standard & edition have you used?
- What make/models/components will you be using?
- What short circuit rating do you support?
- Can you provide relevant design verification documentation?
- What routine checks will you be carrying out?
- Can you arrange for us to inspect?
- Will you share approved drawings?
- Do you include installation/commissioning support?
What are the delivery timescales & warranty?
- Who will provide technical support once dispatched?
The answers should be specific & where required include documentation.
11. Common Mistakes to Avoid
- Going for the cheapest option – A low price may not include all the technical aspects & could have lower quality components.
- Not considering fault levels – The panel should have the correct short circuit withstanding for the electrical system.
- Vague testing – Ask for the actual reports & ensure they know what testing they will be doing.
- No approved drawings – This could cause issues with incorrect sizes, output configurations & cable entries.
- Not checking components – Ensure you know the exact models & ratings.
- Not considering installation environment – Dust, Moisture, Temperature & Ventilation can all affect your panel choice.
- Not knowing what support they will provide – Ensure you know what support & warranty they will provide.
12. Choose Super Elmech Engineers
Super Elmech Engineers Pvt Ltd are an electrical control & distribution panel manufacturer. Their manufacturing site is based in Gurugram, Haryana, India.
They list a wide range of electrical panels including PCC, MCC, APFC, VFD, HVAC, AHU & more specialist panels for industrial, commercial & infrastructural requirements.
Their website states they have an engineering process including AutoCAD General Arrangement sketches, Single Line Diagrams, Control Drawings, Component Planning, Manufacturing & Assembly.
When choosing Super Elmech Engineers for your project in Chennai & Sriperumbudur it is important to provide them with your project specification & confirm the panel configuration, commercial requirements, delivery & support. Don’t assume they have a manufacturing site in Chennai.
Electrical Panel Solutions
Visit the relevant pages:
PCC Panels
MCC Panels
APFC Panels
Thyristor Based APFC Panels
VFD Panels
Testing & Support
About Super Elmech Engineers
Request a Technical Quote
If your company is looking to install a new factory, expand your production or upgrade your electrical distribution system please provide us with your electrical requirements.
Useful information includes Single Line Diagram, Load Schedule, Panel Ratings, Output Information, Operation & Project Requirements.
Contact Super Elmech Engineers Pvt Ltd
Website: https://www.superelmech.com/
Manufacturing Site: Gurugram, Haryana, India
Phone: +91 124 646 0877 / +91 9811129576
Contact us to discuss if they can provide the panel configuration & delivery requirements for your project in Chennai & Sriperumbudur.
13. Frequently Asked Questions
1. How do I find reliable electrical panel manufacturers in Chennai?
Shortlist suppliers based on relevant manufacturing experience, engineering capability, component selection, applicable standards, testing documentation, delivery commitments and after-sales support. Compare technical offers using the same project specification.
2. Which electrical panels are commonly required in industrial facilities?
Industrial facilities may require PCC, MCC, APFC, VFD, AMF, PLC-based control, synchronising and specialised process-control panels. The actual requirement depends on the electrical load and application.
3. What is the difference between PCC and MCC panels?
A PCC panel is mainly used for distributing electrical power to different feeders. An MCC panel is designed to control and protect multiple electric motors through suitable starters, switching and protection devices.
4. Are APFC panels useful for manufacturing plants?
APFC panels can help manufacturing plants manage reactive power demand by automatically switching capacitor bank steps. Their suitability depends on the existing power factor, load variation, harmonic conditions and electricity tariff.
5. What documents should I request from an electrical panel manufacturer?
Depending on the project, request the technical offer, SLD, GA drawing, control schematic, BOM, component datasheets, applicable design-verification documents, inspection records and warranty details.
6. What is the importance of CPRI testing for electrical panels?
CPRI testing can provide evidence that a particular design or assembly has been evaluated for specified performance requirements. Buyers should check the actual report, tested configuration and ratings rather than relying on a general marketing claim.
7. Can an electrical panel manufacturer provide customised panels?
Manufacturers with suitable engineering and production capability may offer customised feeder arrangements, protection, metering, control logic, enclosure dimensions and automation interfaces. All customisation should be reviewed against the project specification.
8. What affects the price of an industrial electrical panel?
Price depends on panel type, voltage and current ratings, fault level, enclosure, busbar design, component makes, protection, automation, testing, documentation, quantity and delivery requirements.
9. Should I arrange a factory inspection before dispatch?
If required by the project, arrange a Factory Acceptance Test or inspection before dispatch. Agree on the test scope, acceptance criteria, inspection records and witness requirements in the purchase order.
10. Does Super Elmech Engineers manufacture electrical panels for Chennai projects?
Super Elmech Engineers is based in Gurugram, Haryana, and lists several industrial and commercial electrical panel solutions. Buyers planning Chennai or Sriperumbudur projects should contact the company to confirm product suitability, delivery feasibility and service arrangements for their specific requirements.
14. Conclusion
Selecting the right electrical panel manufacturer for a Chennai or Sriperumbudur project requires a structured technical and commercial evaluation.
Start by identifying the required panel type and preparing a clear electrical specification. Compare manufacturers on engineering experience, component selection, busbar design, protection, applicable standards, testing, documentation and after-sales support.
Do not make the decision only on the basis of the lowest quotation. A technically suitable panel with clear documentation and an agreed support scope can help reduce procurement risks and avoid operational complications.

